Garage Door Spring Replacement in Centennial
Your garage door repair in Centennial is just around the corner. But just like any other mechanical device requires regular maintenance to perform its best day-in and day-out. This includes cleaning and lubricating your garage door hinges, rollers and track on an annual basis. Cleaning your garage door more or track is the first step. Don’t use water or other chemicals as this can cause build up and do more damage than good. Instead, use a broom to brush off any dust and debris. Be particularly careful to clean out spider webs and other insect nests that might capture other dirt and particles that can clog up the tracks and wheels.
For garage doors in consider doing this seasonally after the brown pine pollen has finished covering the ground. In other areas, the spring is a good time to do maintenance because winter vehicle traffic brings an abundance of dirt and grime into the garage.
Sticking garage doors can be caused by a few issues. If you have a remote garage opener, check batteries, sensors and switches first. If you open the garage door manually, check for obstructions in the wheel track first.Different weather conditions and temperatures can affect the lubricant. Using more of a proper type may help sticking doors. One of the major causes of stuck garage doors is that they are hung unevenly. Make sure all the cables and springs that hold them are even length and have the same springiness from side to side.
The Door Moves Unevenly and Shimmies Side to Side
The easiest way to solve and unevenly opening garage door is by removing an obstruction or debris in the tracks where the wheels run. Clear and clean those first to see if the problem is solved.If not, check the quality of the springs. They should be the same length and stretch the same amount. On doors with automatic openers, the motors that control both sides of the door may be faulty. A replacement may be in order.
Loud Noises When Opening or Closing the Garage Door
Loud screeching, grinding or squealing noises coming from the garage door signifies a problem with dirt or debris in the track or lack of lubrication. Clean the entire track where the door wheels run without harsh cleaners to remove dirt and anything else that could get in the way of a smooth operation.Use oil specially designed for garage doors, or a standard hardware lubricant such as WD-40, on all the door tracks and hardware. Run the door up and down a few times to check that the problem is solved.
Garage Door Falls Too Quickly When Lowering It
A falling garage door can pose a great risk of injury to people who are opening or closing it. This problem is caused by broken cables or overly loose springs. With the door in the closed position, carefully examine all the apparatus to determine what the problem is. Do not replace springs or cables on your own; instead consult a professional garage door repair man. There is several safety hazards related to replacing garage door springs without the proper equipment or knowledge.
Remote Control Door Opener Fails to Work
After checking the batteries and switches to make sure the device is powered up, the garage door still might have problems opening or closing correctly. If none of the above solutions helps – checking cables and clearing the tracks – you may have to either replace the garage opener motor or sensors.
In Centennial go with the best for garage door repair
Top reasons why you need garage door repair. This is part of a continuing series.
8. The disconnect switch was enabled
If you can hear your garage door motor running for what seems like the full amount of time it normally would take to open or close the door, but the door doesn’t move, chances are the disconnect switch has been enabled. Every garage door opener comes with a disconnect switch in case you lose power. This allows you to open or close the door manually so your car isn’t stuck in the garage until the power comes back on.
This switch is usually attached to a rope that can be pulled or a knob that can be turned to disconnect. Sometimes, this switch can accidentally come unhooked causing the door to be disconnected from the motor.
However, if you lose power and use the disconnect switch, you’ll need to reattach it to use your garage door motor to open and close your door again. Open the door all the way and then reattach this hook. Then try opening or closing the door again with your transmitter, and you should be all set. It will be easiest to reattach this hook when your car is not in the garage, as you’ll need to place a step ladder underneath the motor to reach it.
Posted in Denver