Your garage door repair in Thornton is just around the corner. But just like any other mechanical device requires regular maintenance to perform its best day-in and day-out. This includes cleaning and lubricating your garage door hinges, rollers and track on an annual basis. Cleaning your garage door more or track is the first step. Don’t use water or other chemicals as this can cause build up and do more damage than good. Instead, use a broom to brush off any dust and debris. Be particularly careful to clean out spider webs and other insect nests that might capture other dirt and particles that can clog up the tracks and wheels.
For garage doors in consider doing this seasonally after the brown pine pollen has finished covering the ground. In other areas, the spring is a good time to do maintenance because winter vehicle traffic brings an abundance of dirt and grime into the garage.
Safety first with overhead door repair
Operating Your Door While Power Is Out
Pull the rope back and as close to the garage door opener motor as possible. This will keep the rope out of the way while you operate the door in manual mode. Hopefully your power is out for only a short period of time, and you’ll soon return to automatic operation of your garage door opener.
If not, don’t worry. Homeowners used garage doors manually for years before automatic openers became widely available. It’s more effort and certainly less convenient, but a power outage shouldn’t prevent you from using your garage however you like.
What To Do When Power Returns
When the power comes on, you’ll need to reattach your garage door to the automatic opener. Pull down on the handle at the end of the rope again, just as you did when you first disengaged the opener. Then pull up on the door until you hear or feel it snap back into place once more. Alternatively, you can also push the button on your automatic opener. You’ll see the spring attachment reconnect once the opener reaches a certain point — and you’ll be back in business again.
If for any reason your garage door fails to engage again with the automatic opener after a power outage, you may need to call a provider of garage door repairs. It’s always possible that the return of power has led to a power surge that’s made the automatic opener inoperable.
In Thornton go with the best for garage door repair
2. Your Photo Eye Is out of Alignment
You may remember a time as a kid when you and your siblings would close the garage door and run underneath it as fast as possible to make it out before the door closed. Well, on any garage door installed after 1993, that’s no longer possible thanks to two tiny photo eyes on either side of the garage entrance. These photo eyes transmit an invisible beam between each other that detects if anything is in the garage door’s path when it closes. This safety measure is there to prevent automatic garage doors from closing on top of someone or something and causing serious injury or damage to property.
If you notice that the garage door opens normally but doesn’t make any attempt to close when the remote is pressed, the first thing you’ll want to do is visually inspect the photo eyes. Over time, these eyes can get dirty, causing the light from the beam to be blocked. They also can eventually become misaligned, causing the eyes to not match up on both sides.
When cleaning the photo eye, you should take care not to scratch or damage the eye since it’s made of glass, similar to that of a camera lens. The photo eye itself is pretty small, only a few centimeters in diameter, but it can get dirty rather easily. To clean it, you’ll need a soft cloth and a mild, streak-free cleaner. Gently wipe away any dirt or residue that has built up on the eye and be careful not to over saturate as excessive wetness can cause dirt to stick to the eye more quickly.
If your photo eyes are clean and the door still isn’t closing, the next thing you’ll need to do is check the alignment of the eyes. The eyes should be pointing in exactly the same direction and at the same angle. If they’re off, they won’t register that the other one is there, and it’ll assume something is in its path, causing the door to stay in the open position. When checking the alignment, measure the height of each photo eye from the ground. Use a level to make sure they’re pointing directly across at each other at the same angle. A laser level will make this part a little easier, but if you don’t have one, a regular level will work as well.
Once you have the eyes cleaned and aligned, test your door to make sure it opens and closes normally. If you’re still experiencing issues with the photo eyes, it may be time to call the professionals to come out and diagnose the problem.