Garage Door Spring Repair Cost in Morrison

Your garage door repair in Morrison is just around the corner.  But just like any other mechanical device requires regular maintenance to perform its best day-in and day-out. This includes cleaning and lubricating your garage door hinges, rollers and track on an annual basis.  Cleaning your garage door more or  track is the first step. Don’t use water or other chemicals as this can cause build up and do more damage than good. Instead, use a broom to brush off any dust and debris. Be particularly careful to clean out spider webs and other insect nests that might capture other dirt and particles that can clog up the tracks and wheels.

For garage doors in consider doing this seasonally after the brown pine pollen has finished covering the ground. In other areas, the spring is a good time to do maintenance because winter vehicle traffic brings an abundance of dirt and grime into the garage.

24 hour garage door repair is just around the corner

Garage Door Springs

Top reasons why you need garage door repair. This is part of a continuing series.
1. The Transmitter Batteries Are Dead

This may sound obvious, but your garage door transmitters need power to work. If the batteries in your transmitter are dead, the transmitter won’t be able to send a signal to your garage door to open.

Garage Tread
First, check the garage door springs then check the wall inside your garage still opens your garage door when pressed. If it does, then the transmitter in your car likely just needs a simple battery replacement. If you have more than one car transmitter for your garage door, then your other transmitters will likely need new batteries soon as well, since they were probably installed around the same time.

Changing the battery on your garage door transmitter is pretty simple. On most, you can simply slide the door open on the back of the transmitter and remove the battery. Others may be screwed in to keep the battery more secure, so this type of transmitter will require a screwdriver to open.

After removing the old batteries, make sure the plus and minus signs line up with the plus and minus signs on the inside of the transmitter. Otherwise, the new battery won’t work in the transmitter, and it could give you a false sign that something else may be wrong. Once the battery is in place, test the transmitter, and if it works, replace the transmitter door.

In Morrison go with the best for garage door repair

Top reasons why you need garage door repair. This is part of a continuing series.
2. Your Photo Eye Is out of Alignment
You may remember a time as a kid when you and your siblings would close the garage door and run underneath it as fast as possible to make it out before the door closed. Well, on any garage door installed after 1993, that’s no longer possible thanks to two tiny photo eyes on either side of the garage entrance. These photo eyes transmit an invisible beam between each other that detects if anything is in the garage door’s path when it closes. This safety measure is there to prevent automatic garage doors from closing on top of someone or something and causing serious injury or damage to property.

If you notice that the garage door opens normally but doesn’t make any attempt to close when the remote is pressed, the first thing you’ll want to do is visually inspect the photo eyes. Over time, these eyes can get dirty, causing the light from the beam to be blocked. They also can eventually become misaligned, causing the eyes to not match up on both sides.

When cleaning the photo eye, you should take care not to scratch or damage the eye since it’s made of glass, similar to that of a camera lens. The photo eye itself is pretty small, only a few centimeters in diameter, but it can get dirty rather easily. To clean it, you’ll need a soft cloth and a mild, streak-free cleaner. Gently wipe away any dirt or residue that has built up on the eye and be careful not to over saturate as excessive wetness can cause dirt to stick to the eye more quickly.

If your photo eyes are clean and the door still isn’t closing, the next thing you’ll need to do is check the alignment of the eyes. The eyes should be pointing in exactly the same direction and at the same angle. If they’re off, they won’t register that the other one is there, and it’ll assume something is in its path, causing the door to stay in the open position. When checking the alignment, measure the height of each photo eye from the ground. Use a level to make sure they’re pointing directly across at each other at the same angle. A laser level will make this part a little easier, but if you don’t have one, a regular level will work as well.

Once you have the eyes cleaned and aligned, test your door to make sure it opens and closes normally. If you’re still experiencing issues with the photo eyes, it may be time to call the professionals to come out and diagnose the problem.


Garage Door Spring Repair

Denver